MEDAP S VAC

MEDAP S VAC
Powerful tapping unit
for the central
gas supply system

MEDAP S VAC

Excellent combination of best quality and modern design

The different versions of the MEDAP S VAC tapping unit enable silent and extremely powerful aspiration via the terminal unit for vacuum of the central gas supply system. These modern tapping units are extremely lightweight thanks to their impact-resistant ABS plastic housing, and their large, rounded surfaces provide optimum hygienic conditions. A large control valve makes it easy to set the vacuum to the precise level required. Clearly visible ON and OFF buttons on the sides show the unit’s operating status. The MEDAP S VAC is CF-compatible and MR-conditional up to 4.7 teslas.

Easy to use

through a large control valve, large vacuum gauge, and clearly visible ON and OFF buttons

Effective aspiration

through a high vacuum level and an extremely high flow rate of up to 100 l/min

Universal use

thanks to special materials that even allow use in MR environments

Excellent
visual monitoring

The large vacuum gauge with a diameter of 63 mm together with large, clear numbers in kPa and mmHg ensure excellent readability — even from a distance — and a safe workflow.

Indication-specific labelling

Two versions of the MEDAP S VAC are available: one for surgical or bronchial aspiration and one for drainage aspiration. A large, coloured indication label makes it easy to distinguish indications clearly — especially when using multiple tapping units at the same time.

MEDAP S VAC B 900 for surgical and bronchial aspiration
MEDAP S VAC D 200 for drainage aspiration

MR-conditional

Made using special materials
MR-conditional up to 4.7 teslas

ON and OFF buttons as a slide switch

The ON and OFF buttons are clearly visible. The markings make it easy to recognise the corresponding setting.

Versions

Tapping units

ATMOS offers the MEDAP S VAC B 900 for surgical and bronchial aspiration as well as the MEDAP S VAC D 200 for drainage aspiration in a variety of connection forms.

MEDAP S VAC D 200

MEDAP S VAC B 900

Wall and equipment rail connections

DIN

MEDAP

Equipment rail

Technical Data

	MEDAP S VAC B 900	MEDAP S VAC D 200
Article number	HM57525620, HM57525619, HM57525621, HM57525622, HM57525623, HM57525624, HM57525625	HM57525627, HM57525626, HM57525628, HM57525629, HM57525630, HM57525631, HM57525636
Gas type	Vacuum	Vacuum
Suction capacity	100 l/min	90 l/min
Max. vacuum	–100 kPa –1000 mbar	–20 kPa –200 mbar
Vacuum control range	0 to –100 kPa	0 up to –20 kPa
Connection to CGS / gas pin	Wall: DIN. MEDAP. BS. NF. SS. equipment rail. screw fittings	Wall: DIN. MEDAP. BS. NF. SS. equipment rail. screw fittings
Nominal pressure, gas supply	–100 to –60 kPa	–100 up to –60 kPa
MR safety	up to 4,7 teslas	up to 4.7 teslas
Dimensions (H x W x D)	165 x 80 x 125–165 mm	165 x 80 x 125-165 mm
Weight	360–510 g	410–560 g

FAQ

Why does the MEDAP S VAC have a label for specific indications?

Two versions of the MEDAP S VAC are available: one for surgical or bronchial aspiration and one for drainage aspiration. Both versions look the same except for the different vacuum gauge scales. In the intensive care unit, a patient may require both bronchial and drainage aspiration. To avoid confusion, special indication labels show the respective indication.

What function does the hole have on the back of the MEDAP S VAC D 200?

The hole is a safety valve on the patient side that opens at a pressure of 20 kPa and ensures that the maximum vacuum of 20 kPa is not exceeded during drainage.

Why is the DIN gas pin on the MEDAP S VAC so long?

In some intensive care units, the terminal units are in wall channels. An equipment rail often runs just beneath the terminal units. If an overflow protection device is used below the MEDAP S VAC, it could collide with the equipment rail of the wall channel. Therefore, the length of the DIN gas pin was designed in such a way that the MEDAP S VAC cannot come into conflict with the equipment rail even if an overflow protection device is used.

Why can’t the vacuum connection tube to the septic fluid jar be connected directly to the MEDAP S VAC?

In accordance with the international standard ISO 10079 for medical suction equipment, the use of a hydrophobic overflow protection device and a bacterial filter is mandatory. The MEDAP S VAC has the same connection as the MEDAP S AIR. That means the same adapter, and therefore the same hydrophobic bacterial and viral filter, can be connected to the MEDAP S VAC as to the MEDAP S AIR.

Downloads

Title	Date	Extension	Size	Language
Brochures & Flyers
Brochure ATMOS Medical Suction Systems	07.09.2023	pdf	3.58 MB	en, ru, cn, hu
Brochure ATMOS Suction with Central Gas Supply Systems (CGS)	22.03.2021	pdf	1.96 MB	en, fr, ru, cn, es, hu
Brochure MEDAP Medical Suction Systems	22.03.2021	pdf	1.40 MB	en, ru, cn, hu
Brochure MEDAP S VAC	22.03.2021	pdf	501.30 KB	en, fr, ru, cn, es, hu
Technical Documentation
Declaration of Conformity / Konformitätserklärung Accessories Overflow Protection / Zubehör Überlaufschutz	31.08.2022	pdf	188.62 KB	de, en, fr, cn, es, hu
Declaration of Conformity / Konformitätserklärung Suction unit, vacuum / Absauggerät, Vakuum	27.03.2024	pdf	143.98 KB	de, en, fr, cn, es, hu
Operating Instructions MEDAP S VAC B 900 / D 200	30.05.2022	pdf	1.28 MB	en, cn, es, hu